Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Spring Replacement Cost in Seven Hills?
Spring replacement in Seven Hills typically costs $180 – $340 per spring, and since most doors run a matched pair, a full replacement usually lands around $360 – $680. The exact figure depends on the spring type, the door’s weight, and how the job is set up in your garage. These are typical estimated ranges for the Seven Hills market in 2026, and the written estimate we give you sets the final price.
Spring work is the most safety-critical part of any garage door. Torsion springs hold enough stored energy to cause serious injury if they let go, so this isn’t a job to tackle with tools from the hardware store. The technicians we connect you with handle this every week. Our technicians have up to 15 years of experience. Call (844) 443-4563 for a free estimate. We answer 24/7, and fast dispatch from 7am to 7pm gets most Seven Hills homeowners a same-day visit.
Key Takeaways
- One spring: typically $180 – $340. A matched pair: roughly double that.
- Most doors have two springs and are best replaced as a set.
- Torsion and extension springs price differently, and door weight matters.
- Free estimates, and the written estimate is the price.
- For the full service behind these numbers, see spring replacement.
Spring Replacement Cost Breakdown (2026)
Here’s how the numbers break down for a typical Seven Hills job. Each line is an estimated range, not a fixed quote.
| Item | Typical estimated range |
|---|---|
| Single torsion spring (one spring) | $180 – $340 |
| Matched pair of springs | $360 – $680 |
| Single extension spring (one spring) | $180 – $340 |
| Spring repair (ranges overlap the above) | $180 – $340 |
| Cable repair (often done with springs) | $130 – $250 |
| Roller replacement (while the door is open) | $110 – $220 |
| General garage door repair | $150 – $600 |
What pushes a spring job toward the top of the range? Heavier doors need thicker springs, and a door that’s out of balance or has been running on a broken spring for a while often needs cables, rollers or a track adjustment too. Doors with rusted or seized hardware take longer to open up safely. What pulls it toward the bottom: a single light door, standard two-car width, and hardware that still moves freely. If your springs are original to a house that’s been in Seven Hills for a while, the surrounding parts usually show the same wear, so it’s worth having the local pro look at the whole assembly rather than just the spring.
The number on your estimate reflects the actual spring on your door, the labor for your specific setup, and any parts that need replacing. That’s why we don’t quote a flat price over the phone before we see the door.
What Affects Spring Replacement Pricing in Seven Hills
- One spring or a pair. A single spring runs $180 – $340. A matched pair is usually replaced together because the two springs wear at the same rate, so a pair costs about twice a single spring. Replacing just one when both are the same age often means a second visit soon after.
- Torsion versus extension. Torsion springs mount on a shaft above the door and handle more weight, while extension springs run along the sides. Both fall in our $180 – $340 per-spring range, but the labor and spring size can differ from one door to the next. If you’re not sure which you have, take a quick photo before you call.
- Door weight and width. A single-car door carries lighter springs than a double-car door. Insulated doors weigh more than uninsulated ones, so they need heavier springs, and that shows up in the parts cost. If you’ve added a new door recently, mention it so the estimate accounts for it.
- Condition of cables, rollers and track. Springs rarely fail alone. Cables fray, rollers flat-spot, and the track can shift, and these add $110 – $250 depending on what’s replaced. Doing them at the same time as the springs costs less than a second visit.
- Rust and age of hardware. Older doors with seized bolts and rusted drums take longer to open up safely. A Seven Hills garage sees wide swings from hot summer afternoons to freezing winter nights, and that cycle works on metal parts year after year. Hardware that’s been exposed to that kind of temperature change often needs more time and sometimes parts to free up.
- Access and door height. Tall doors, tight garages with low ceilings, and doors close to shelving or stored items all add labor time. Clearing a path to the door before the technician arrives is free and shortens the visit.
The temperature swings across the Front Range matter more than many homeowners expect. Springs work-harden and can snap without warning, especially after a cold snap, and a door that ran fine all summer can fail on the first cold morning. That’s not a sales pitch; it’s the physics of a spring doing its job through thousands of cycles. When one lets go, you’ll usually hear a sharp bang from the garage. At that point the door shouldn’t be forced open or closed by hand.
How to Save on Spring Replacement
You don’t cut corners on a spring, but you can avoid paying for the same visit twice. A few practical ways to keep the cost down:
- Replace the pair, not one spring. Two springs of the same age fail close together. Paying for one now and one in a few months usually costs more in total than replacing both at once.
- Bundle worn parts into the same visit. If your rollers are flat or a cable looks frayed, add them to the spring job. A roller set runs $110 – $220, and a cable repair $130 – $250, but both cost less when the door is already open and the technician is on site.
- Get a free estimate before you commit. A written estimate tells you exactly what’s included. There’s no service-call fee and no diagnostic charge; the estimate is free. Call (844) 443-4563 and we’ll set it up.
- Clear the garage before the visit. A clear path to the door and open space around the tracks means less setup time, and setup time is part of the labor.
- Don’t wait for a second spring to break. A door running on one broken spring stresses the opener and the cables. Catching it before the opener fails saves the cost of opener repair too, which runs $120 – $320.
- Ask about the door, not just the spring. If the door is near the end of its life, a technician can tell you whether replacing it makes more sense than throwing money at an old assembly. A new door installation runs $700 – $2,200, so it’s worth knowing where you stand.
We work on the brand already in your garage, so the estimate is based on your actual door, not a generic package. Whether it’s a Clopay, Amarr, Wayne Dalton, Raynor or any other common residential door, the spring sizing and the parts are matched to what you have. Parts come from a parts-stocked operation, so common springs and hardware aren’t sitting on back order while your car sits in the driveway.
FAQs – Spring Replacement Cost
How much does spring replacement cost in Seven Hills?
Spring replacement in Seven Hills typically costs $180 – $340 for one spring, and a matched pair usually runs about twice that, so $360 – $680. The exact price depends on the spring type, the door’s weight, and whether cables or rollers need replacing at the same time. Call (844) 443-4563 for an exact quote. Estimates are free.
Is it cheaper to repair a spring or replace it?
Replacing is the standard answer, because a broken spring can’t be repaired and a tired one that’s still holding is usually near the end of its life. A single spring replacement runs $180 – $340, and replacing the pair together costs about twice one spring but saves a second visit later. Call (844) 443-4563 and we’ll give you a written estimate before any work starts.
How much does it cost if both springs break in Seven Hills?
A pair of springs typically runs $360 – $680, since each single spring is $180 – $340 and a matched pair is replaced together. If the door was forced, cables or rollers may need replacing too, which can add $130 – $250. Call (844) 443-4563 for a free estimate on the whole job. We answer 24/7.
Can you come today for a broken spring in Seven Hills?
Yes, same-day service is available for most spring calls in Seven Hills. Fast dispatch runs from 7am to 7pm, Sunday through Friday. Call (844) 443-4563; a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Leave the door closed and don’t try to lift it by hand in the meantime, because a door with a broken spring is dangerously unbalanced.
Why does the estimate vary so much from one door to the next?
Because the spring itself varies. A light single-car door needs a smaller, less expensive spring than a heavy insulated double door, and the labor changes with door height, ceiling clearance, and the condition of the cables, rollers and track. The $180 – $340 per-spring range covers most residential doors in Seven Hills, with hardware add-ons in the $110 – $250 range. Call (844) 443-4563 for an estimate that reflects your actual door.
Do you need a permit for spring replacement in Seven Hills?
Usually not. Spring replacement is a repair to an existing door assembly and typically doesn’t require a permit, but rules can vary, so check with the city’s building department if you’re unsure. The bigger issue is safety: torsion springs store enough force to break a wrist or worse, so this isn’t a do-it-yourself job. Call (844) 443-4563 and let a trained technician handle it.
Why the Spring Matters More Than the Price
A spring replacement that’s done right lasts for years and keeps the rest of the system healthy. A cheap spring that’s the wrong size for the door wears out faster, strains the opener, and can leave the door out of balance. That’s why we size the spring to your door rather than reaching for whatever’s on hand, and why we check the cables, rollers and track as part of the estimate. You’re paying for the right part and the labor to install it safely, not for a guess.
Our technicians are familiar with the eight major brands you’re most likely to have in the garage already: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor. That covers spring, cable and opener work on the same visit, so you’re not coordinating three separate vendors to get one door working. Whether you’re keeping a legacy opener alive or running a current LiftMaster or Chamberlain myQ setup, the spring is the foundation everything else sits on.
If you want to see how a full spring job is handled from start to finish, and what our overall repair service covers, start with garage door repair in Seven Hills and then call for a free estimate. The written estimate is the price you pay; no surprises at the end.
Get a Free Estimate on Your Springs
If your door banged this morning and won’t lift, or you’ve noticed a gap in the spring above the door, don’t wait for it to fail completely. Call (844) 443-4563 for a free estimate. We answer 24/7, and fast dispatch from 7am to 7pm, Sunday through Friday, gets a technician to your Seven Hills garage. You’ll get a written estimate before any work begins, and the estimate sets the final price.
Pricing reflects the Seven Hills market as of 2026. Garage Door Repair Seven Hills offers free estimates – call (844) 443-4563.
Written by the team at Garage Door Repair Seven Hills.
What Our Customers Say
"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Kelly Novak"Spring snapped at six in the morning with my car sealed inside and me due at work. Somebody was here by eight thirty and had it fixed that morning. Door's quieter now than it was before it broke."
- Gabriela Reyes"Opener kept reversing halfway down. Turned out to be the safety sensors knocked out of alignment by a bicycle. He straightened them, wouldn't charge me for it, and just asked me to keep them in mind if I need real work later."
- Kevin Kowalski